Netgear Concept and Installation

We use NETGEAR  router for connecting our broadband with our computers.

Here I give you the easy way of configuring / installing the netgear.

1. Connect the Modem to the Internet port of the NETGEAR router and the computer to any of the four LAN ports as shown in the diagram.
   
2. Open an Internet Explorer browser and type the router IP address which would be either http://192.168.0.1 orhttp://192.168.1.1 in the address bar and press Enter.
3. • The Login window will prompt for the router configuration username and password.
   • The default username is “admin” and the default password is “password”
      
4. Click Setup Wizard on the top left corner, Select Yes for the Setup Wizard to detect the type of internet connection and click Next.
   
5. The Setup Wizard will detect the type of Internet connection. For Cable Internet connections, Setup Wizard will detect Dynamic IP. Click Next
   
6. You do not have to change the default settings unless your ISP has given you specific DNS information which must be configured.
   
7. The router will now save these settings. When complete, you can verify whether you are connected to the internet from the Router Status > Maintenance menu.
   
   Verify you have a valid IP address (not-blank / 0.0.0.0) on the Internet Port assigned by your ISP 

Long Beep Sound

At times, we will be experiencing a long beep sound in our computers that without the computers ceased its booting process and there is no display in the monitor.

This happens due to RAM problems.  We can switch OFF the system and then open the  CPU.  Then remove the RAM from the slot with much care and slightly use erase to clean the copper portions on the RAM.  Insert it into the slot and switch On the system.  This is work fine.  If the RAM is faulty then, replace it.  Otherwise call your engineer for help.

NO FOLDER OPTIONS / SEARCH OPTION :

If there is no Folder Options / Search Option in no doubt there is some malware in your system. Just download some malware remover like ‘mbam.exe’ and run it.

One thing to note is that it's quite possible that if you're in an environment managed by a centralized policy, these settings may have no effect. Your IT administrator may set things up so as to disable Task Manager, and other things as well at the domain level. You'll need to ask them if this is the case.

PING not recognized

If Ping not recognized error is coming just type 'Set'

Set

check whether Path C:\WINDOWS\system32

If not found in the command prompt type : path=C:\WINDOWS\system32

Thats it the things is over

http://payingptr.com/pages/index.php?refid=sengueny

System.EXE Error

If your system is giving some popups with system.exe, then it is seriously infected by a spyware / Trojan. To overcome this a download a free version of TROJAN REMOVER http://www.simplysup.com/tremover/download.html which is available with 30 days validation and solve the issue.

NET SEND for console message transmission

This is a command used to send messages through out the network
Syntax : NET SEND {name * /DOMAIN[:name] /USERS} message
Example : NET SEND auro This is a test message
Common problems in it : Error 2273 and 2136
Soultions : First enable the messenger services for all the PCs. This can be done by Start -> Run -> type services.msc
In the pop up locate messenger, in the start type select Automatic and start the service.

How to set up Internet in Local Area Network

Use Proxy System
There are lots of proxy available for download in free such as Analog Proxy, CCProxy, etc. There are many draw backs in using Proxies. The proxy installed PC should be kept ON always for other computers to work internet. Also, some proxies restrict gives access to few pcs only. Some is hard to config work with outlook express and MS outlook.

To overcome the above, the following can be done.

Setting each PC to access internet separately.

First complete as usual connections with the modem like power chord & telephone line.Then take a separate line from modem and connect the other end to the router / switch. network lines are connected.

Now, configure the system which needs internet as below :
Let us assume that the following may be interproviders IP setup
Now open the network properties (step as given above) of the PC which needs to access internet.
Click Advanced and in the IP settings then Add and enter IP address as ‘192.168.1.10’
In default Gateway click add and enter 192.168.1.1